When in 270(n) or 300(n) mode the router is not very good at switching off the extra channels when not needed or when it may cause interference to other wireless access points.įor this reason please use these modes responsibly.Įnabled = reduce dead spots in the wireless coverage Wireless radio channelwidth=20 sgi=disabled Wireless radio channelwidth=20/40 sgi=enabled Wireless radio channelwidth=20/40 sgi=disabled Wireless radio channelwidth=20 sgi=enabled Undo - Enable all wireless speeds (TG587n only) CommandĬhange wireless n speed (TG582n only) Command Remove WAN from “interface group” (ie disabled) - Default Service system ifdelete name=PING_RESPONDER group=wan Undo - Disable reply to Pings from WAN - Default mode Service system ifadd name=PING_RESPONDER group=wanĪdd to WAN “interface group” (ie enabled) Service system list name=PING_RESPONDER expand=enabledĬheck if “interface group” is associated with WAN (ie enabled) Service system modify name=CWMP-C state=enabled Service system modify name=CWMP-S state=enabled Undo - Enable CWMP - default mode Command Service system modify name=CWMP-C state=disabledĭisable checking for firmware updates etc “phone home”. Service system modify name=CWMP-S state=disabled See note (1) Replace “xx” with your spoof MACĭisable CWMP - Remote management by the ISP Command Ip ifconfig intf=Internet hwaddr=00:xx:xx:xx:xx:xx Script add name=useroot command=”user add name=me password=pass role=root”Ĭhange “me” and “pass” for your own username and password. User config name=Administrator password=mypasswordĬreate username with “root” privileges. Must be an existing username ie “SuperUser” or “Administrator” User config name=SuperUser password=mypassword
#Wow client freeze logout exit 2017 password
CommandĬhange router password - I’ve found this troublesome using the web interface. Useful if your ISP sometimes has congested gateways. With some ISP connections this may change your gateway it may also change your IP address. Use one of the above commands then saveall ! Xdsl debug multimode config=t1.413issue2+g992.5_annex_a Xdsl debug multimode config=t1.413issue2+g992.3_annex_a Xdsl debug multimode config=t1.413issue2+g992.1_annex_a Ie resetting the modulation to default (ie no change) can be used to force the router to perform a resync. See Telnet Scripting for a method to get these stats quick.įorce connection modulation mode to ADSL1, ADSL2 or ADSL2+ (also disable Annex M)Ī useful byproduct of this command is that it causes a resync. Host - enter your opendns network label or enter the catch all - Ĭheck the routers event log to confirm “dyndns host has been updated”. Go to the routers web interface Toolbox > Dynamic DNS > Configure :. Go to, sign in with your OpenDNS username / password.
#Wow client freeze logout exit 2017 update
(10800 seconds)Įnsure your opendns account is set to - enable dynamic IP update View existing settings - It’s the “custom” section we’ll be changingĭyndns service modify name=custom server= updateinterval=10800 Para se utilizar dyndns para actualizar o OpenDNS Command Para se usar OpenDNS (Firmware 108): Commandĭns server forward dnsset add set=0 dns=208.67.222.222 metric=0 intf=Internetĭns server forward dnsset add set=0 dns=208.67.220.220 metric=0 intf=Internet May need to reboot or renew the ppp session to obtain the DNS settings. Undo, return to obtaining DNS resolvers via DHCP Command The ISP DNS settings may creep back in over time.Ī metric value of 0 has been used to give these new DNS settings priority over any ISP settings.Įg the lower the metric the higher the priority. List all DNS resolvers set in the router. See note (1) below regarding “intf=Internet”ĭns server route add dns=8.8.4.4 metric=0 intf=Internet ( optional )ĭns server route add dns=8.8.8.8 metric=0 intf=Internet (Os comandos foram achados na internet e a GCT não se responsabiliza por problemas causados pelo o utilizador.)ĭeve-se entrar no cmd e colocar telnet 192.168.1.254 (192.168.1.254 é o endereço do vosso router).ĭe seguida a linha de comandos vai pedir o utilizador e a password, após a autenticação os comandos podem ser usados.Īlguns dos comandos necessitam de acesso root. Aqui temos uma lista de comandos telnet para utilização em routers technicolor que a MEO e a Vodafone utilizam.